Electronics

New heat spreading tech delivers 740% increase in circuit power density

View 2 Images
Experimental configurations showed outstanding cooling capability for the central conformal copper heat spreader, which performed as well as the the chunky heat sinks on the right, while taking up far less space
University of Illinois
Experimental configurations showed outstanding cooling capability for the central conformal copper heat spreader, which performed as well as the the chunky heat sinks on the right, while taking up far less space
University of Illinois
The heat spreader is created by coating the components with a layer of parylene C for electrical insulation, then adding a 20 nm thick layer of electro-less copper via physical vapor deposition, and then adding a further 50 nm of copper by electroplating
University of Illinois

A team from the University of Illinois and UC Berkeley has demonstrated a new cooling method that sucks heat out of electronics so efficiently that it allows designers to run 7.4 times more power through a given volume than conventional heat sinks.

Heat is very much the enemy for electronics designers, and it's one of the key limiting factors preventing electronics from getting smaller. If heat can't be ejected from circuits, they break down functionally, and sometimes physically. The familiar stacked-wafer shape of heat sinks is designed to conduct heat away from sensitive areas and dissipate it where it won't cause trouble, but the team says they typically can't remove heat from the underside of devices, where a lot of it is generated.

Next-generation heat spreaders seek to improve on the traditional heat sink, but the team says they're typically made out of expensive materials like diamond, and they often can't mount directly to the surface of the components without a layer of "thermal interface material" that improves contact, but can inhibit thermal performance.

The team has come up with a solution they say radically boosts heat ejection without introducing costly materials. A new study published in the peer-reviewed journal Nature Electronics describes an approach that "first coats the devices with an electrical layer of poly(2-chloro-p-xylylene) (parylene C) and then a conformal coating of copper. This allows the copper to be in close proximity to the heat-generating elements, eliminating the need for thermal interface materials."

The heat spreader is created by coating the components with a layer of parylene C for electrical insulation, then adding a 20 nm thick layer of electro-less copper via physical vapor deposition, and then adding a further 50 nm of copper by electroplating
University of Illinois

Essentially, this new cooling system completely covers all exposed surfaces of the electronics, including the top, the bottom and the sides. The device and the heat spreader act as a single piece, which performs as effectively, or more effectively, than a heat sink, without anywhere near the bulk of one. The team tested this ultra-efficient passive cooling approach successfully on some gallium nitride power transistors.

For a single circuit, they recorded impressive results – but the effect is greatly multiplied when you can stack them on top of one another. “Let’s say you have multiple printed circuit boards,” says lead author and UIUC Ph. D student Tarik Gebrael. “You can stack many more printed circuit boards in the same volume when you are using our coating, compared to if you are using conventional liquid- or air-cooled heat sinks ... And this translates to much higher power per unit volume. We were able to demonstrate a 740% increase in the power per unit volume.”

The research confirmed that this conformal copper coating is suitable for use in both air- and water-cooled applications, although further testing is needed to see how durable this solution will be in boiling water, boiling dielectric fluids, high-voltage applications, and in circuits more complex than the simple test rigs used in the study.

The paper is available in the journal Nature Electronics.

Source: University of Illinois

  • Facebook
  • Twitter
  • Flipboard
  • LinkedIn
2 comments
paul314
Does this require new chip packing and wiring so that the copper can get close to where it needs to be, but not where it would short everything? Probably still good for situations where volume is at an absolute premium
Treon Verdery
This wonderful to hear about, it is likely researchers have already though about this but could the fluoro version of poly(2-chloro-p-xylylene) be an even better heat conductor? Also newatlas has an article on isotopically pure silicon wires, would using deuterium, a few hundred $/Kg, instead of hydrogen at the parylene-c change heat conduction. Also parylene-c researchers have likely already compared different crystallinity/amorphous forms for better cooling. An idea that has a slight chance of working is a very thin liquid metal gallium indium Cu layer to provide liquid metal cooling advantages.